Aeroflow V-band kits with a centering ring for precise fitment.
Flanges, gaskets & hw, Page 1
Copper locking nuts for a tight sealLeaking exhausts are a common problem. A leaking sound, low boost pressure and a failed emission test are all problems which can be caused by a leaking exhaust.Copper locking nuts are the best nuts you can use, because they dont come loose like their iron cousins due to thermal expansion.Especially turbo gaskets will also fail quickly after the bolts have come loose, and that will result in a kind of screaming sound.The copper locking nuts are stocked and readily
A simple weldable lambda nut for adding a lambda fitting to an exhaust.
Steel 10 mm flanges for Garrett and Holset turbocharger inlet, outlet and oil fittings.
A small y-joint to use in headers or manifold joints for example.
Exhaust sleeves to use in joining different pipe diameters in palces where an actual cone reducer wont fit.
Exhaust reducers in stainless or mild steel.Models with three diameters can be cut to fit a pipe with the middle diameter as well.An exhaust pipe reducer allows a diameter change with minimal flow restrictions.
Fits inside a 2.5" exhaust tubing. When installed at the end of an exhaust system, helps lower especially low frequency noise.Total length 285mm.
Electric exhaust valves allow mild sounds while streeting, and roaring exhaust sounds on the track.A valve can open and close the exhaust flow. Examples of use are a screamer pipe directly after the downpipe, or a muffler bypass.Available in 2.25", 2.5" or 3" diameters as electically or vacuum controlled.
Exhaust DIY parts include straight pipes, reducers as well as regular and tight angles in stainless or mild steel.You can filter the list by selecting the material and diameter. Reducers are also shown on the same list if they fit the selected diameter.All pipes are Scandinavian quality.We also carry all other exhaust flanges, clamps, gaskets, silencers and catalyzers.
Nissan Maxima / 350z VQ20DE, VQ30DE and VQ35DE exhaust manifold gasket. Sold per piece.
Clampco V-bands Clampco V-bands matches original-quality and is made by USA manufacturer, Clampco.In racing use high quality band means solid fitment and quick release for maintenance.Also available as stainless steel, AISI 304 flanges, as well as with old black flanges.
Thicker threads and body assure these exhaust U-clamps wont shear threads or bend like the usual single-use clamps.
T-bolt clamps Clamps are stainless steel and ensure and even pressure around the pipe, preventing crushing and jamming.These are basically the slimmest way to fasten an exhaust pipe and can be used in very tight compartments. The millimeter size is an exact figure, where the inch size is the common exhaust diameter the clamp is intended to be used with.We stock all T-bolt clamps in our shop.
The CRC exhaust assembly paste Sealing, heat-resistant, no asbestos. Remove the loose dirt. Apply the paste evenly with a connection and install. Exhaust gas heat causes it to harden. Keep out of the reach of children. Avoid contact with skin and eyes.
CRC Exhaust repair tape fixes holes and tears in an exhaust pipe. A handy fix when there's no time or sense to install a new exhaust.
Weldable exhaust flanges These weldable mild-steel flanges are laser-cut, and offer an easy way of making quality joints for custom exhausts.Mild-steel is the best option for flanges since it has minimal deformation compared to stainless steel flanges. Basically most factory-made stainless exhausts also have mild-steel flanges.Thickness is 10 mm. The flanges are sold per piece, so please order two for each full joint.In addition to these we offer copper locking nuts, exhaust gaskets, and affordable cat
2- and 3-bolt exhaust gaskets from 2 to 3.5" sizes.
Nissan 200sx SR20DET exhaust manifold gasket. Other SR20DET gaskets are also available in our webshop and from our sales.Check out the complete listing of engine gaskets.