Accessory belts, tensioners and guides from quality brands like Contitec and Gates.
Engine & trans, Page 9
Quality spare valve seals for Nissan 200sx SR20DET and CA18DET engines.The CA18DET set is sold for the complete engine.The SR20DET are sold per intake or exhaust side. In case of an SR20DET red top, check the exhaust valve diameter, as some SR engines have the 6 mm exhaust valves and you should get two intake side kits.
Siemens DEKA 630cc injectors.Our injectors are matched sets within 1% of each other. These are high-ohm (12,6 ohm) injectors, and for example in the Nissan CA18DET the injector resistor should be bypassed.O-ring to O-ring length 64mm.Flow: 630cc/min @ 3bar 727cc/min @ 4barOther names / codes for this injector: -Siemens FI114961 -Mototron INJ-GAS-006 -Accel 74620L -MSD/Edge 2030
OEM Waterpumps OEM-quality water pumps for well-known manufacturers.Car water pump is generally belt drive vane pump, which circulates engine coolant. Although the water pump does not use the timing belt, it is worth it to frequently change, as in many cases the water pump is located at the place where it requires removing the timing gear.Water pump range includes mostly the best selling pumps. Please contact our sales if your car is not found in our range.
Full engine gasket kit for Nissan ca18det-engine.
Top / head gasket kit for the ca18det -engine(s). This quality set is made by Reinz, and keeps water, pressure and oil where they belong even in tuned engines.For head gaskets we suggest an MLS gasket for high power cars.
Nissan 200sx SR20DET fwd head gasket made by Reinz. This is an affordable spare part which is suitable for engines which are not going to be tuned further than 200hp.We have many other options and gaskets for the SR20DET, so check out our engine gaskets category.
Nissan 200sx CA18DET head gasket made by Reinz. This is an affordable spare part which is suitable for engines which are not going to be tuned further than 200hp.Check out the complete listing of engine gaskets.
Head bolt set for Nissan 200SX CA18det-engine. m11x1.5 157mm Manufacturer: AJUSA.
Tomei SR22 stroker kit. Please ask our sales for details and options for this kit.
Tomei RB28 Stroke kit. Please ask our sales for details and options for this kit!
Aluminum pulley kits reduce rotating mass, and result in more responsiveness and less power loss.Bling? Well they add a certain amount of bling as well.Contitech and Gates belts are also available in our webshop.
Billet throttlebody with 65, 70, 80, 90 or 100mm ID. The throttlebody is used to allow more air into the engine when the gas pedal is pressed. A bigger throttlebody allows more air into the engine especially with upgraded intake manifolds. Throttle response is also increased due to a larger bore.This can be used to make an adapter plate to fit other bolt patterns or welded to the existing manifold.A bracket for a Bosch tps is included, but any tps can be made to fit with some craftmanship. The bracket ca
An extended large-volume oil pan for the Nissan VQ35 engine found on the Nissan 350z.
Large volume lower oilpan for the Nissan SR20DET rwd engines.
A bleed valve to rise boost pressure Most turbo cars have a wastegate which regulates boost pressure. By lowering the regulating pressure with a bleed valve, the boost pressure going to the engine can be increased.Our bleed is capable of bleeding out air and regulating the pressure going to the wastegate. This is one of our top selling items and most of the time is in stock.
The DV4 dump valve is a hose-type atmospheric dump valve with a crisp swoosh sound.The kit includes a set of springs which allow adjustment of how easily the dump valve opens. Fitting 25mm hose.We also have other Race.Fi dump valves, Turbosmart dump valves as well as turbochargers and intercoolers.
An affordable bypass which can be installed as a bypass to recirculate boost to the intake pipe, or as atmospheric.Fitting diameter is 25mm. The kit includes a set of springs which enable you to adjust how easily the dump opens. It is also possible to fine-tune the opreation with shims.We also have other Race.Fi dump valves, Turbosmart dump valves as well as turbochargers and intercoolers.
A dump valve releases excess pressure when the throttle body closes. Without a dump valve the excess pressure would flow in the wrong direction through the turbocharger slowing it down or even damaging it in the worst case.This is an affordable adjustable basic valve for cars with up to 300 hp. The dump is adjustable, and releases the pressure in the atmosphere.The kit includes vacuum hoses and a gasket for the flange.Flange bolt (M6) distance 60mm. Flange hole diameter 30mm.The outlet side has a th
Toyota 2JZ-GTE intake manifold. This is a kit intake manifold which converts the original manifold to a better flowing version. The original manifold is cut, and the flange (included) is welded on to allow mounting this manifold.The kit includes hoses, the flange and adapters for installation. Throttle body PCD 85x85mm with 81mm diameter. The Race.Fi 80mm billet throttle body is a bolt on unit.You might also be interested in billet throttlebodies and Mishimoto intercoolers.
RB25DET RB26-style intake manifold A properly flowing intake manifold for the Nissan RB25 DET engine. The kit changes the position of the throttle body to face forward like the RB26 manifolds. This kit is essential with front mount intercoolers, or when you're cleaning up the engine compartment. Having a front facing throttle body allows for shorter and cooler intake pipes when used with a front mount intercooler.This manifold is made for a bigger throttle body, so the stock body either needs modifying or you
Nissan SR20DET Black Top intake manifold. A better flowing intake manifold for the Nissan 200sx SR20DET Black Top engines. This manifold is a high-volume upgrade to the original manifold.The stock idle control valve will fit. The kit also includes hoses and adapters for installation. Runnsers should be ported according to the head or manifold gasket.Throttle body diameter is 65mm with a 60x60 mm pcd. A suitable tb is the Race.fi 65mm billet throttle body for example.You might also be interested in Mish
Nissan SR20DET Red Top intake manifold. A better flowing intake manifold for the Nissan 200sx SR20DET Red Top engines. This manifold is high-volume upgrade to the original manifold. Most EU cars come with the Black Top engine, so please check your cars original manifold and our SR20DET Black Top manifold as well to be sure.The stock idle control valve will fit. The kit also includes hoses and adapters for installation. Runners should be ported according to the gasket.Throttle body diameter is 65mm with a 6
2.0L 4G63 EVO V-IX 97-07, 2.4L 4G64 EVO I-IV 92->, 2.4L 4G64 EVO V-IX 97-07, 2.4L DOHC 16v 4G69, 2.0L SOHC 8v Diesel 4D68 Reference: ACL 5M1219H std